Update 7/16/2020:You can use these without a light switch all together. I got a little creative and just mounted one on two gang switch plate mounted to a one gang electrical box. used this Switch to separate A light and ceiling fan which I’ve wanted to do for a long time. This is only possible if you have A neutral in your light switch box and also a separate dedicated hot wire in your ceiling box. I happen to have both of these so I did not have to run any power to either box to make this work. I hardwired the lights with hue bulbs and the toggle switch on the wall I replaced with a lutron caseta fan dimmer and then wired it so that the switch only controls the fan and not the lights which are now hardwired because they are hue bulbs which can be controlled by the lutron aurora I was actually intending to cut open the wall and put a two gang electrical box in so that I could attach the switch plate to a two gang electrical box, but when I went to do that I realized that the electrical box was sandwiched by two studs so I could not put a two gang box in. I was actually intending to cut open the wall and put a two gang electrical box in so that I could attach the switch plate to a two gang electrical box, but when I went to do that I realized that the electrical box was sandwiched by two studs so I could not put a two gang box in. My solution was to use a bolt about the thickness of a toggle switch. I had to use a washer so the end of the bolt wouldn’t go through the toggle switch hole because The hole was a little bit too wide. After I mounted the Aurora on the end of the bolt I screwed the bolt in just enough to tighten it flush to the switch plate. I had to use a razor blade to gouge a hole in the wall so the switch plate was it flush even though there was a bolt sticking out in the back of it. But this hole that I gouged was much smaller than the hole I was going to cut to add a two gang box so that’s fine. To get the finely threaded switch plate screws I picked up some mr grip form my local big box hardware store. Maybe they sell it on amazon too? Not sure. It’s metal strips you can cut to size with teeth. It’s meant to fix stripped holes in wood and things. In this case screwed the switch plate screws directly into the drywall and then backed them out then I cut multiple tiny strips of the metal and shoved them in holes. After I put enough strips in there the switch plate screws did end up grabbing onto the metal so I could secure them to the drywall.The end result was that I had two switches and a nice switch plate on the wall, one controlled my lights and the other one control my fan. From the outside appearance you would never know that there isn’t actually a switch in the wall or even a two gang electrical box. You can see the end result in the very last picture. It is the one with the fan dimmer on the right and the aurora on the left.Update 4/6/2020:We’ve had these installed for a while now and my son very much enjoys taking them off the wall. He does it with ease and lately he has Raised his interest in this hobby. Yesterday during bath he left the tub, climbed the step stool up to the switch, pulled it off and put it in the tub, and then Proceeded to start pushing the button while it was submerged. Surprisingly, it worked in the tub and continued to work after I pulled it back out and away from the little hands that had it. I decided to set it on a continuously running air purifier for the evening to be on the safe side but I’m not even sure that was necessary. To this moment it is still working! So in case you have some small hands in the house hold you can rest assured, that it is indeed waterproof At least to a certain point.. I guess?Summary: This switch is perfect for some areas of our house. I wish it had more flexibility in terms of controls like the hue dimmer remote (namely the ability to have multiple presses control different scenes and homekit support), but where that isn’t completely necessary, this works well. It can, however, be rigged to control homekit devices through homekit automations with hue bulbs. We ended up putting some on normal toggle switch plates for now but some we have put in all decora style switch plates that we really like by using an adapter from amazon (more on that in 4th paragraph under “style”). Beware though, toddlers love to push the button and I wouldn’t say this thing is super durable.Style:The switch looks pretty good but in my opinion could look better. As you may be able to tell, it looks a lot like one of those cheap rotary dimmers. That is just as true in real like as it is in the pictures. This could be looked at as good or bad. If you are going for the high tech modern look I’m afraid I wouldn’t say this item really fills that need. If you are looking for something that looks normal, blends in, and is functional then this will be perfect for you. I have only a couple of complaints about the style.Namely that the base for this white switch is grey? Which I can’t make any sense of. I think it would look better if the base was white, maybe even more modern. I’m not sure what the motivation was behind the seeable base being grey.And secondly the light that lights up in the switch during use is just a small dot in the top (pictured) I think it would look better if they would have made just the center of Switch glow in its entirety, but due to the construction of this switch that might of been too difficult to engineer?We wanted to use them with all decora style plates we really liked and we were able to do that by using adapters which you can find on amazon by searching “Toggle Switch Adapter Plate“. The one we used was about $12 and made by a brand called taymac. You can see the end result in the picture, it turned out pretty well. The aurora switch doesn’t completely cover the adapters’ depression but it almost covers it and it’s hardly noticeable what of the depression isn't covered.Durability:I would not recommend using this switch in super rugged scenarios or if you are going to have this switch in direct reachability of a toddler who loves to “push the button”. It is pretty easy to remove (my 2 year old has no problem with that), and it is also possible to break the clip to fasten the switch to the base. I haven’t personally broken it, but I received a warehouse deal that I am returning which has a broken clip (so most likely someone else broke it and returned it). Aside from it getting broken I’d also be scared for it to go missing. It’s quite small and if it ended up in some crevice I’m not sure how or if we’d ever find it again. I’ve had to completely take it off the wall a couple times when my two year old is having a little too much fun with it.Also, in general, this switch just seems cheaply made. I’m not too upset for the amount of tech you get packed into this tiny little device for such an affordable price, I wouldn’t expect much more. But you just have to be careful.Functionality:It works well. It does the job. The two main purposes of this switch are equally successfully fulfilled. Even when my toddler takes the switch off the wall, he still can’t flip the switch underneath with the base installed (and he tried). It also obviously keeps any unknowing guests from turning off your smart lighting which was a main concern for Me.As far as lighting the lights goes. Yes it works. Sometimes there is a very slight delay, but really maybe half a second or something. It’s not bad. It’s not as seamless as a regular switch.. But when all your lights are hooked into a network you can’t really expect it to be. That being said if a delay at all will bother you, you may want to consider the hue dimmer remote switch, I’ve found less delay with that. (there are switch plates you can Find on the internet That hold the remote magnetically and cover the switch just like this dimmer too, just search hue dimmer switch plate and they should come up. Keep in mind they are rough 3D printed plastic they’ll need to be sanded and painted to look as perfect as a store bought switch plate but they work well ). But still like i said the delay is only sometimes there and it’s minimal when it is there.It can be flipped upside down to lock a switch in the opposite position (for example for three way switches or switches put in upside down). The light in the switch even automatically rotates to the other side of the switch to accommodate the new direction.On this switch only the side of the switch turns when dimming not the whole switch like on a cheap rotary dimmer. The center of the switch never rotates. Also, only the center of the button can be pushed in not the whole switch, like the cheap rotary dimmers. Not that that matters to me but maybe it’s notable for some people.If you’re worried about set up and installation don’t be. The whole process is less than a few minutes per switch including both installing dimmer over The toggle switch and hooking it up to the lights in the hue app. It’s very easy, fast, and self explanatory. Go to accessory set up in settings panel in hue app. Then click on friends of hue and Lutron aurora is right on top for me. It tells you exactly how to set up the switch right in the hue app, I didn’t hardly need the instruction manual and I didn’t need any kind of Lutron app at all.My only complaint here is that I wish they would implement the ability to double or triple tap to activate different scenes. In the areas of the house where we needed this option we just bought the hue dimmer remote switch, but since I know the aurora is capable of this (you have to double and/or triple tap during set up) I wish they would add it as a feature of the lighting abilities too. For now all you can do is just set up which scene you want activated (or last on state) and it is what it is.Also you cannot use this to control anything else in home kit like you can with the hue remote dimmer switch because this is not a homekit device. It works with the hue lights and nothing else so if you were hoping to have this control other devices or set a scene in homekit it won’t work. You could do a work around with an automaton if you really wanted to (set an automation in homekit: if the bathroom light turns on/off then the bathroom fan turns on/off) but you cannot just make a button press activate a homekit scene or accessory otherwise. We have now done this with a light on a homekit scent diffuser (made by vocolink for $50) that we placed in our bathroom. I currently have it set up to turn on green when the bathroom light is turned on during the day and turn off when the bathroom light is turned off. It works with near 100 percent accuracy and sometimes the diffuser light comes in a smidgen quicker than the bathroom light some how. I also have the diffuser light come on to a more night time like color after a certain hour at night too which is possible because you can put time restraints on your automations in homekit. You cannot, however, use homekit automatons to dim and brighten a homekit device (as in the diffuser light) when you dim and brighten the hue light with the aurora switch. There is no way to set that up, it can only be triggered by an on/off. You can however set what brightness you’d like your homekit device to turn onto when your hue light comes on. But it will always turn on to that same brightness with the exception, of course, of putting time restraints on it (before 5pm turn to 100% brightness after 5 pm turn to 50% brightness.. etc).Over all I’m pretty happy with this switch and we have now purchased multiple for different areas of the house and they all work well with the exception of the ones that arrived broken.Works great! It does what it’s supposed to, and (like any well designed products should) it “just works”. Setup is honestly so easy, that after spending $50 on the thing, it feels kind of weird to spend less than 5 minutes doing things with it, and then just be done. It just sits there - but it works when you need it, and it solves the forever annoying problem of having people flip the switches the wrong way!I put one in my guest bedroom, as there are three separate lamps controlled by the group in there, and people staying over inevitably mess with them all. After liking the simplicity of it, I decided to add one to our main bedroom as well, as it’s nice to just not have to say “Alexa, turn on the lights” sometimes! Sometimes you’re closer to the switch, or one person is already asleep and you don’t want to wake them to add a little light (the rotate to turn on slightly dim feature is really nice) - and sometimes when you’re, er, spending “private time”, it’s nice to be able to dim the lights down low without having to shout at Alexa to do it, and kill the mood ;)Setup literally does take just five minutes - you screw the thing on (easy, but if you buy the one without the screwdriver, you’ll want a small glasses-type screwdriver to do it), go to the accessory section of the app and add the switch, pick the room(s) you want it to control (the hard work was already done when you set up the room setups), and that’s it! I like to go in to the accessory settings, and change the default setting to “Last on state”, so it remembers the dimness/color settings from when you last turned it off, which is what you’d expect it to do anyways (don’t know why that isn’t the default already). And that’s really it! Then you just let it be, and use it when you need it! Philips Hue adds a nice dimming effect when turning it off and on, which is a nice touch as well!If I had any complaints (and they’d be extremely minor), these are the things I’d mention:- Not a problem with the switch per-se, but when using the dimming functionality in a room with multiple separate lamps, Hue has a tendency to not perfectly sync the bulbs, resulting in a weird offset dimming effect that is slightly off-putting. In no ways a deal breaker, and not something the switch designers can really control, but it’s worth noting as you might notice it occasionally.- Just a personal design aesthetic for me, but I think the little white light that flashes on the switch when you toggle it would look better in the middle of the switch, rather than the top. Might be a limitation of the design (that’s where the old switch is underneath), however.- The switch does stick out a bit more than a “regular” dimmer switch, with a little bit of the grey plastic from the mount showing underneath. Not a big deal, as you get used to the look pretty quickly, but it looks a little unusual at first if you’re expecting something exactly like a normal dimmer switch, or expecting the switch to snap fully down over the mounting plastic. It really does look nice however - see my images for an example!- It’s a bit pricey for what it is - but it IS part of the Hue ecosystem, so what do you expect ?‍♀️. It serves its purpose well, so as far as I’m concerned, it’s worth the money. I have the official Hue dimmer switch/remote in my living room, which is definitely cheaper, and also works really well - however it doesn’t serve the dual purpose of covering the switches to keep people from flipping them. This depends on your experience, but I’d argue that feature alone is worth some money, especially in rooms where guests/others who don’t know the system are likely to be using the lights. The Hue dimmer is perfect in my living room, where there are no readily accessible switches anyways, and having the removable remote to put on the coffee table is a nice touch! I mounted it where a switch Should be in my house, and it works great. Each is their own thing really, and they each have their own well-suited purposes!A note to people who don’t have ‘standard‘ light switches (necessary to place this on): if you’re reasonably comfortable with DIY, it’s pretty easy (and cheap - a good switch and plate together cost like ~$2-3) to just buy a new switch at a hardware store, and wire it in. Look up a video for how to do it online, be SURE to turn off the power at the panel before working on things, and if you’re in any way uncomfortable or don’t know what you’re doing, call an electrician. I’m not one - I’m just a random person on the internet, so I can’t be held responsible for anything that comes of your choice to follow my instructions - however it really is easy to do once you know what you’re doing, and it can allow you to use this switch even if you have the flat-style “decor” switches, or existing dimming knobs. I actually used these both on switches I replaced from some very old dimmers, which had a tendency to buzz, and cause the Hue bulbs to act wonky when the dimmer wasn’t turned up to 100%.That’s it, really! It works well, it solves a problem that all smarthome owners know and experience, and it does so in a sleek, elegant, and easy to use way!A note to Amazon: I have no idea what the “Sheerness” rating you’re asking me for is, as I can’t for the life of me figure out what about this product is “sheer” ?.When we bought our new house, I was committed to making it smart. I had already dabbled in Hue and SmartThings for years, but wanted to transition to HomeKit and Homebridge. Now that our new house doesn’t have a neutral wire in the switch boxes, I was limited to Lutron Caseta and lamps (1980’s build). Fortunately, Lutron brought out the aurora dimmer and it really solves most of my smart home issues. The Hue bulbs would get turned off at the switch, making them dumb bulbs again. But now guests and family can “hit the switch” and the Hue bulbs function as nature intended.My only complaint is it is unclear which hub the Aurora connects to. My hue hub and my Lutron hub are not next to each other so I experienced some connectivity issues in the beginning, which was resolved when I moved the two hubs closer to each other and more central in the house.Over all I’m thrilled with these little godsends.These work really well on their own. Easy to install, the battery lasts forever (couple years and still claim 100%), and the Hue lights don’t flicker when dimmed.A bit expensive for the whole Lutron/Hue package, but I had spent twice as much on different dimmers and LED bulbs that always flickered when dimmed. Only the really old Philips LED bulbs ever worked without obvious flickering for me.If you have some programming background and desire the “all 4 hue” iPhone app gives you the ability to turn these Lutron switches into a multifunctional device. I have mine configured to run specific scenes based on the time of day and sunrise/set. With a double click they run a 15-min gradual wake-up scene. I’m even turning off other rooms in the house when it’s late and all the bedroom lights have been triggered with these switches.Unlike a few other reviewers, I do not have any problem with the build quality. The lights can be turned on/off with a tap -- this would feel a bit more natural if the entire button tapped in/out, rather than just the entire centre console (leaving a thin circle that does not tap). I do not know about battery life -- have not had it that long. The lag is comparable with say a smartphone app controller, about what I expect. In its default out-of-box config, it turns that lights to maximum brightness when tapped-out ... I think I would have preferred it to maintain the prior brightness level. Also would be nice to be able to play with the light temperature points - it seems to warm the light a bit as it dims, but more control would be nice. Possibly an app other than the default Philips Hue control app might let me do this (I am using the Lutron dimmer with a Hue hub).To connect to the Hue hub, I did have to do a couple hard resets on the Lutron dimmer. Not sure why, but this was easy enough and the initial connection was at least able to identify the Lutron dimmer and thus easily give me the reset instructions (it was connected, but would not control the lights it was supposed to control). All worked fine after a couple reconnects -- about par for any modern electronic device these days, it seems.I admit that I would love to see these around the $20-30 mark, but at the end of the day, they are a product I'm happy to spend $50 for. When it comes to smart devices in a house, I absolutely love smart lights, but their usefulness tends to break down once you start to factor in other people. I'm happy to tinker with things and set customized routines and triggers without thinking of it, but what about family, friends, or guests? Its something new that they might only temporarily or rarely be exposed to, and the more removed it is from 'flip switch get light' the more annoyed people are likely to get.When it comes to convenience, I've played around with Philips Hue switches before because they get closer to the "standard light switch package", but I haven't found anything more directly effective than this. It first deals with the problem of 'how do people interact with lights' via allowing people to either press the switch to turn it on/off, and allows for people to control a dimmer feature via spinning the dial. But, more importantly, it locks operation of the light switch. I currently live in an apartment so I cannot connect or disconnect certain plugs from a switch, and there are times that I do not want a light switch to be operational - like, for example, if the switch connects to a plug that powers my computer or other devices I expect to stay on. Installation of this over a switch stops that switch from being fiddled with, while still letting easy control of lights.Even when you're not dealing with something that wants/assumes constant power, smart lights losing power can be a bit of a pain in the butt in the first place: Philips Hue has a 'power on' default now (thankfully), but I'm not sure about their competitors. It at least means that you're not going to have strange reactions when lights are powered on, but lights that are off will never respond to a remote command. Locking the switch on means that this isn't an issue, and the ease of operation by anyone who isn't even tech-inclined means that the switch being locked on won't be an issue.I love home kit including smart lights but the insanely frustrating problem is people (mostly guests and even my own kids) flip my Philips hue switches off leaving them unresponsive. I’ve been looking for a solution for a long time and have finally found it. Yes, $50 is steep but worth every penny. Easy to install, works effortlessly and looks nice. No scenes but you can select a different default scene (like “last on” or “energize” and others). I did have to replace my decora switch with a toggle which wasn’t ideal but a small price to pay. I also had to spend $20 on a new wall plate that fit 1 toggle and 2 decora. Lutron apparently makes a decora insert but good luck finding this product anywhere. Anyways, totally recommend. I have 7 more switches that control hue lights that I will be replacing with the Aurora.Works great once setup, but the setup process was a nightmare. I have never had issues with any other hue or friends of hue products, bit this took over an hour to get working. The range seems to be inferior to the hue remotes, and it costs about double what those do. Once setup, it is pretty nice, but sometimes fails to respond, unlike the hue remotes that she to always work perfectly. Overall, I would recommend the first party totes from Philips unless you are very particular about the look.La instalación es muy sencilla y agregarlos al bridge Hue fue muy fácil. Tienen un botón central que prende y apaga la luz y la perilla baja y sube la intensidad de la luz. El botón central se siente frágil, no se presiona parejo. Si lo presionas de arriba, solamente esa parte se presiona y el resto se inclina y pareciera que se va a romper o a salir. Le pondría 4.5 estrellas si se pudiera.